1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
|
/****************************************************************************
* drivers/input/stmpe811_adc.c
*
* Copyright (C) 2012 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* References:
* "STMPE811 S-Touch� advanced resistive touchscreen controller with 8-bit
* GPIO expander," Doc ID 14489 Rev 6, CD00186725, STMicroelectronics"
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <unistd.h>
#include <assert.h>
#include <errno.h>
#include <debug.h>
#include <nuttx/arch.h>
#include <nuttx/input/stmpe811.h>
#include "stmpe811.h"
#if defined(CONFIG_INPUT) && defined(CONFIG_INPUT_STMPE811) && !defined(CONFIG_STMPE811_ADC_DISABLE)
/****************************************************************************
* Private Types
****************************************************************************/
/****************************************************************************
* Private Data
****************************************************************************/
/****************************************************************************
* Private Functions
****************************************************************************/
/****************************************************************************
* Public Functions
****************************************************************************/
/****************************************************************************
* Name: stmpe811_adcinitialize
*
* Description:
* Configure for ADC mode operation. Set overall ADC ADC timing that
* applies to all pins.
*
* Input Parameters:
* handle - The handle previously returned by stmpe811_instantiate
*
* Returned Value:
* Zero is returned on success. Otherwise, a negated errno value is
* returned to indicate the nature of the failure.
*
****************************************************************************/
int stmpe811_adcinitialize(STMPE811_HANDLE handle)
{
FAR struct stmpe811_dev_s *priv = (FAR struct stmpe811_dev_s *)handle;
uint8_t regval;
int ret;
DEBUGASSERT(handle);
/* Get exclusive access to the device structure */
ret = sem_wait(&priv->exclsem);
if (ret < 0)
{
int errval = errno;
idbg("sem_wait failed: %d\n", errval);
return -errval;
}
/* Enable Clocking for ADC */
regval = stmpe811_getreg8(priv, STMPE811_SYS_CTRL2);
regval &= ~SYS_CTRL2_ADC_OFF;
stmpe811_putreg8(priv, STMPE811_SYS_CTRL2, regval);
/* Select Sample Time, bit number and ADC Reference */
stmpe811_putreg8(priv, STMPE811_ADC_CTRL1, priv->config->ctrl1);
/* Wait for 20 ms */
up_mdelay(20);
/* Select the ADC clock speed */
stmpe811_putreg8(priv, STMPE811_ADC_CTRL2, priv->config->ctrl2);
/* Mark ADC initialized */
priv->flags |= STMPE811_FLAGS_ADC_INITIALIZED;
sem_post(&priv->exclsem);
return OK;
}
/****************************************************************************
* Name: stmpe811_adcconfig
*
* Description:
* Configure a pin for ADC input.
*
* Input Parameters:
* handle - The handle previously returned by stmpe811_instantiate
* pin - The ADC pin number
*
* Returned Value:
* Zero is returned on success. Otherwise, a negated errno value is
* returned to indicate the nature of the failure.
*
****************************************************************************/
int stmpe811_adcconfig(STMPE811_HANDLE handle, int pin)
{
FAR struct stmpe811_dev_s *priv = (FAR struct stmpe811_dev_s *)handle;
uint8_t pinmask = GPIO_PIN(pin);
uint8_t regval;
int ret;
DEBUGASSERT(handle && (unsigned)pin < STMPE811_ADC_NPINS);
/* Get exclusive access to the device structure */
ret = sem_wait(&priv->exclsem);
if (ret < 0)
{
int errval = errno;
idbg("sem_wait failed: %d\n", errval);
return -errval;
}
/* Make sure that the pin is not already in use */
if ((priv->inuse & pinmask) != 0)
{
idbg("PIN%d is already in-use\n", pin);
sem_post(&priv->exclsem);
return -EBUSY;
}
/* Clear the alternate function bit for the pin, making it an ADC input
* (or perhaps an an external reference, depending on the state of the
* ADC_CTRL1_REF_SEL bit).
*/
regval = stmpe811_getreg8(priv, STMPE811_GPIO_AF);
regval &= ~pinmask;
stmpe811_putreg8(priv, STMPE811_GPIO_AF, regval);
/* Mark the pin as 'in use' */
priv->inuse |= pinmask;
sem_post(&priv->exclsem);
return OK;
}
/****************************************************************************
* Name: stmpe811_adcread
*
* Description:
* Read the converted analog input value from the select pin.
*
* Input Parameters:
* handle - The handle previously returned by stmpe811_instantiate
* pin - The ADC pin number
*
* Returned Value:
* The converted value (there is no error reporting mechanism).
*
****************************************************************************/
uint16_t stmpe811_adcread(STMPE811_HANDLE handle, int pin)
{
FAR struct stmpe811_dev_s *priv = (FAR struct stmpe811_dev_s *)handle;
uint8_t pinmask = GPIO_PIN(pin);
uint8_t regval;
int i;
int ret;
DEBUGASSERT(handle && (unsigned)pin < 8);
/* Get exclusive access to the device structure */
ret = sem_wait(&priv->exclsem);
if (ret < 0)
{
int errval = errno;
idbg("sem_wait failed: %d\n", errval);
return -errval;
}
/* Request AD conversion by setting the bit corresponding the pin in the
* ADC CAPT register.
*/
stmpe811_putreg8(priv, STMPE811_ADC_CAPT, pinmask);
/* Wait for the conversion to complete. The ADC CAPT register reads '1'
* if conversion is completed. Reads '0' if conversion is in progress.
* Try three times before giving up.
*/
for (i = 0; i < 3; i++)
{
/* The worst case ADC conversion time is (nominally) 56.4 uS. The
* following usleep() looks nice but in reality, the usleep()
* does not have that kind of precision (it will probably end up
* waiting 10 MS).
*/
usleep(57);
/* Check if the conversion is complete */
regval = stmpe811_getreg8(priv, STMPE811_ADC_CAPT);
if ((regval & pinmask) != 0)
{
break;
}
}
/* At the completion of the conversion, return whatever we read from
* from the channel register associated with the pin.
*/
return stmpe811_getreg16(priv, STMPE811_ADC_DATACH(pin));
}
#endif /* CONFIG_INPUT && CONFIG_INPUT_STMPE811 && !CONFIG_STMPE811_ADC_DISABLE */
|
