/************************************************************************************
* arch/arm/src/lm3s/lm3s_internal.h
*
* Copyright (C) 2009-2010 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <spudmonkey@racsa.co.cr>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __ARCH_ARM_SRC_LM3S_LM3S_INTERNAL_H
#define __ARCH_ARM_SRC_LM3S_LM3S_INTERNAL_H
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
#include <stdint.h>
#include <stdbool.h>
#include "up_internal.h"
#include "chip.h"
/************************************************************************************
* Pre-processor Definitions
************************************************************************************/
/* The LM3S69xx only supports 8 priority levels. The hardware priority mechanism
* will only look at the upper N bits of the 8-bit priority level (where N is 3 for
* the Stellaris family), so any prioritization must be performed in those bits.
* The default priority level is set to the middle value
*/
#define NVIC_SYSH_PRIORITY_MIN 0xe0 /* All bits set in minimum priority */
#define NVIC_SYSH_PRIORITY_DEFAULT 0x80 /* Midpoint is the default */
#define NVIC_SYSH_PRIORITY_MAX 0x00 /* Zero is maximum priority */
/* Bit-encoded input to lm3s_configgpio() *******************************************/
/* Encoding:
* FFFS SPPP IIIn nnnn nnnn nnnn VPPP PBBB
*
* These bits set the primary function of the pin:
* FFFn nnnn nnnn nnnn nnnn nnnn nnnn nnnn
*/
#define GPIO_FUNC_SHIFT 29 /* Bit 31-29: GPIO function */
#define GPIO_FUNC_MASK (7 << GPIO_FUNC_SHIFT) /* (See table 9-1 in data sheet) */
#define GPIO_FUNC_INPUT (0 << GPIO_FUNC_SHIFT) /* Digital GPIO input */
#define GPIO_FUNC_OUTPUT (1 << GPIO_FUNC_SHIFT) /* Digital GPIO output */
#define GPIO_FUNC_ODINPUT (2 << GPIO_FUNC_SHIFT) /* Open-drain GPIO input */
#define GPIO_FUNC_ODOUTPUT (3 << GPIO_FUNC_SHIFT) /* Open-drain GPIO output */
#define GPIO_FUNC_PFODIO (4 << GPIO_FUNC_SHIFT) /* Open-drain input/output (I2C) */
#define GPIO_FUNC_PFINPUT (5 << GPIO_FUNC_SHIFT) /* Digital input (Timer, CCP) */
#define GPIO_FUNC_PFOUTPUT (5 << GPIO_FUNC_SHIFT) /* Digital output (Timer, PWM, Comparator) */
#define GPIO_FUNC_PFIO (5 << GPIO_FUNC_SHIFT) /* Digital input/output (SSI, UART) */
#define GPIO_FUNC_ANINPUT (6 << GPIO_FUNC_SHIFT) /* Analog input (Comparator) */
#define GPIO_FUNC_INTERRUPT (7 << GPIO_FUNC_SHIFT) /* Interrupt function */
#define GPIO_FUNC_MAX GPIO_FUNC_INTERRUPT
/* That primary may be modified by the following options
* nnnS SPPP nnnn nnnn nnnn nnnn nnnn nnnn
*/
#define GPIO_STRENGTH_SHIFT 27 /* Bits 28-27: Pad drive strength */
#define GPIO_STRENGTH_MASK (3 << GPIO_STRENGTH_SHIFT)
#define GPIO_STRENGTH_2MA (0 << GPIO_STRENGTH_SHIFT) /* 2mA pad drive strength */
#define GPIO_STRENGTH_4MA (1 << GPIO_STRENGTH_SHIFT) /* 4mA pad drive strength */
#define GPIO_STRENGTH_8MA (2 << GPIO_STRENGTH_SHIFT) /* 8mA pad drive strength */
#define GPIO_STRENGTH_8MASC (3 << GPIO_STRENGTH_SHIFT) /* 8mA Pad drive with slew rate control */
#define GPIO_STRENGTH_MAX GPIO_STRENGTH_8MASC
#define GPIO_PADTYPE_SHIFT 24 /* Bits 26-24: Pad type */
#define GPIO_PADTYPE_MASK (7 << GPIO_PADTYPE_SHIFT)
#define GPIO_PADTYPE_STD (0 << GPIO_PADTYPE_SHIFT) /* Push-pull */
#define GPIO_PADTYPE_STDWPU (1 << GPIO_PADTYPE_SHIFT) /* Push-pull with weak pull-up */
#define GPIO_PADTYPE_STDWPD (2 << GPIO_PADTYPE_SHIFT) /* Push-pull with weak pull-down */
#define GPIO_PADTYPE_OD (3 << GPIO_PADTYPE_SHIFT) /* Open-drain */
#define GPIO_PADTYPE_ODWPU (4 << GPIO_PADTYPE_SHIFT) /* Open-drain with weak pull-up */
#define GPIO_PADTYPE_ODWPD (5 << GPIO_PADTYPE_SHIFT) /* Open-drain with weak pull-down */
#define GPIO_PADTYPE_ANALOG (6 << GPIO_PADTYPE_SHIFT) /* Analog comparator */
/* If the pin is an interrupt, then the following options apply
* nnnn nnnn IIIn nnnn nnnn nnnn nnnn nnnn
*/
#define GPIO_INT_SHIFT 21 /* Bits 23-21: Interrupt type */
#define GPIO_INT_MASK (7 << GPIO_INT_SHIFT)
#define GPIO_INT_FALLINGEDGE (0 << GPIO_INT_SHIFT) /* Interrupt on falling edge */
#define GPIO_INT_RISINGEDGE (1 << GPIO_INT_SHIFT) /* Interrupt on rising edge */
#define GPIO_INT_BOTHEDGES (2 << GPIO_INT_SHIFT) /* Interrupt on both edges */
#define GPIO_INT_LOWLEVEL (3 << GPIO_INT_SHIFT) /* Interrupt on low level */
#define GPIO_INT_HIGHLEVEL (4 << GPIO_INT_SHIFT) /* Interrupt on high level */
/* If the pin is an GPIO digital output, then this identifies the initial output value:
* nnnn nnnn nnnn nnnn nnnn nnnn Vnnn nnnn
*/
#define GPIO_VALUE_SHIFT 7 /* Bit 7: If output, inital value of output */
#define GPIO_VALUE_MASK (1 << GPIO_VALUE_SHIFT)
#define GPIO_VALUE_ZERO (0 << GPIO_VALUE_SHIFT) /* Initial value is zero */
#define GPIO_VALUE_ONE (1 << GPIO_VALUE_SHIFT) /* Initial value is one */
/* This identifies the GPIO port
* nnnn nnnn nnnn nnnn nnnn nnnn nPPP Pnnn
*/
#define GPIO_PORT_SHIFT 3 /* Bit 3-6: Port number */
#define GPIO_PORT_MASK (15 << GPIO_PORT_SHIFT)
#define GPIO_PORTA (0 << GPIO_PORT_SHIFT) /* GPIOA */
#define GPIO_PORTB (1 << GPIO_PORT_SHIFT) /* GPIOB */
#define GPIO_PORTC (2 << GPIO_PORT_SHIFT) /* GPIOC */
#define GPIO_PORTD (3 << GPIO_PORT_SHIFT) /* GPIOD */
#define GPIO_PORTE (4 << GPIO_PORT_SHIFT) /* GPIOE */
#define GPIO_PORTF (5 << GPIO_PORT_SHIFT) /* GPIOF */
#define GPIO_PORTG (6 << GPIO_PORT_SHIFT) /* GPIOG */
#define GPIO_PORTH (7 << GPIO_PORT_SHIFT) /* GPIOH */
#define GPIO_PORTJ (8 << GPIO_PORT_SHIFT) /* GPIOJ */
/* This identifies the bit in the port:
* nnnn nnnn nnnn nnnn nnnn nnnn nnnn nBBB
*/
#define GPIO_NUMBER_SHIFT 0 /* Bits 0-2: GPIO number: 0-7 */
#define GPIO_NUMBER_MASK (7 << GPIO_NUMBER_SHIFT)
/* The following lists the input value to lm3s_configgpio to setup the alternate,
* hardware function for each pin.
*/
#if defined(CONFIG_ARCH_CHIP_LM3S6918)
# define GPIO_UART0_RX (GPIO_FUNC_PFINPUT | GPIO_PORTA | 0) /* PA0: UART 0 receive (U0Rx) */
# define GPIO_UART0_TX (GPIO_FUNC_PFOUTPUT | GPIO_PORTA | 1) /* PA1: UART 0 transmit (U0Tx) */
# define GPIO_SSI0_CLK (GPIO_FUNC_PFIO | GPIO_PORTA | 2) /* PA2: SSI0 clock (SSI0Clk) */
# define GPIO_SSI0_FSS (GPIO_FUNC_PFIO | GPIO_PORTA | 3) /* PA3: SSI0 frame (SSI0Fss) */
# define GPIO_SSI0_RX (GPIO_FUNC_PFINPUT | GPIO_PORTA | 4) /* PA4: SSI0 receive (SSI0Rx) */
# define GPIO_SSI0_TX (GPIO_FUNC_PFOUTPUT | GPIO_PORTA | 5) /* PA5: SSI0 transmit (SSI0Tx) */
# define GPIO_TMR1_CCP (GPIO_FUNC_PFIO | GPIO_PORTA | 6) /* PA6: Capture/Compare/PWM1 (CCP1) */
# define GPIO_I2C1_SDA (GPIO_FUNC_PFODIO | GPIO_PORTA | 7) /* PA7: I2C1 data (I2C1SDA) */
# define GPIO_TMR0_CCP (GPIO_FUNC_PFIO | GPIO_PORTB | 0) /* PB0: Capture/Compare/PWM0 (CCP0) */
# define GPIO_TMR2_CCP (GPIO_FUNC_PFIO | GPIO_PORTB | 1) /* PB1: Capture/Compare/PWM2 (CCP2) */
# define GPIO_I2C0_SCL (GPIO_FUNC_PFOUTPUT | GPIO_PORTB | 2) /* PB2: I2C0 clock (I2C0SCL) */
# define GPIO_I2C0_SDA (GPIO_FUNC_PFODIO | GPIO_PORTB | 3) /* PB3: I2C0 data (I2C0SDA) */
# define GPIO_CMP0_NIN (GPIO_FUNC_PFINPUT | GPIO_PORTB | 4) /* PB4: Analog comparator 0 negative input (C0-) */
# define GPIO_CMP1_NIN (GPIO_FUNC_PFINPUT | GPIO_PORTB | 5) /* PB5: Analog comparator 1 negative input (C1-) */
# define GPIO_CMP0_PIN (GPIO_FUNC_PFINPUT | GPIO_PORTB | 6) /* PB6: Analog comparator 0 positive input (C0+) */
# define GPIO_JTAG_TRST (GPIO_FUNC_PFINPUT | GPIO_PORTB | 7) /* PB7: JTAG ~TRST */
# define GPIO_JTAG_TCK (GPIO_FUNC_PFINPUT | GPIO_PORTC | 0) /* PC0: JTAG/SWD CLK */
# define GPIO_JTAG_SWCLK (GPIO_FUNC_PFINPUT | GPIO_PORTC | 0) /* PC0: JTAG/SWD CLK */
# define GPIO_JTAG_TMS (GPIO_FUNC_PFIO | GPIO_PORTC | 1) /* PC1: JTAG TMS */
# define GPIO_JTAG_SWDIO (GPIO_FUNC_PFIO | GPIO_PORTC | 1) /* PC1: JTAG SWDIO */
# define GPIO_JTAG_TDI (GPIO_FUNC_PFINPUT | GPIO_PORTC | 2) /* PC2: JTAG TDI */
# define GPIO_JTAG_TDO (GPIO_FUNC_PFOUTPUT | GPIO_PORTC | 3) /* PC3: JTAG TDO */
# define GPIO_JTAG_SWO (GPIO_FUNC_PFOUTPUT | GPIO_PORTC | 3) /* PC3: JTAG SWO */
# define GPIO_TMR5_CCP (GPIO_FUNC_PFIO | GPIO_PORTC | 4) /* PC4: Capture/Compare/PWM5 (CCP5) */
# define GPIO_CMP1_PIN (GPIO_FUNC_PFINPUT | GPIO_PORTC | 5) /* PC5: Analog comparator 1 positive input (C1+) */
# define GPIO_CMP0_OUT (GPIO_FUNC_PFOUTPUT | GPIO_PORTC | 5) /* PC5: Analog comparator 0 output (C0o) */
# define GPIO_TMR3_CCP (GPIO_FUNC_PFIO | GPIO_PORTC | 6) /* PC6: Capture/Compare/PWM3 (CCP3) */
# define GPIO_TMR4_CCP (GPIO_FUNC_PFIO | GPIO_PORTC | 7) /* PC7: Capture/Compare/PWM4 (CCP4) */
# define GPIO_UART1_RX (GPIO_FUNC_PFINPUT | GPIO_PORTD | 2) /* PD2: UART 1 receive (U1Rx) */
# define GPIO_UART1_TX (GPIO_FUNC_PFOUTPUT | GPIO_PORTD | 3) /* PD3: UART 1 transmit (U1Tx) */
# define GPIO_SSI1_CLK (GPIO_FUNC_PFIO | GPIO_PORTE | 0) /* PE0: SSI1 clock (SSI1Clk) */
# define GPIO_SSI1_FSS (GPIO_FUNC_PFIO | GPIO_PORTE | 1) /* PE1: SSI1 frame (SSI1Fss) */
# define GPIO_SSI1_RX (GPIO_FUNC_PFINPUT | GPIO_PORTE | 2) /* PE2: SSI1 receive (SSI1Rx) */
# define GPIO_SSI1_TX (GPIO_FUNC_PFOUTPUT | GPIO_PORTE | 3) /* PE3: SSI1 transmit (SSI1Tx) */
# define GPIO_ETHPHY_LED1 (GPIO_FUNC_PFOUTPUT | GPIO_PORTF | 2) /* PF2: LED1 */
# define GPIO_ETHPHY_LED0 (GPIO_FUNC_PFOUTPUT | GPIO_PORTF | 3) /* PF3: LED0 */
# define GPIO_I2C1_SCL (GPIO_FUNC_PFOUTPUT | GPIO_PORTG | 0) /* PG0: I2C1 clock (I2C1SCL) */
#elif defined(CONFIG_ARCH_CHIP_LM3S6432)
# define GPIO_UART0_RX (GPIO_FUNC_PFINPUT | GPIO_PORTA | 0) /* PA0: UART 0 receive (U0Rx) */
# define GPIO_UART0_TX (GPIO_FUNC_PFOUTPUT | GPIO_PORTA | 1) /* PA1: UART 0 transmit (U0Tx) */
# define GPIO_SSI0_CLK (GPIO_FUNC_PFIO | GPIO_PORTA | 2) /* PA2: SSI0 clock (SSI0Clk) */
# define GPIO_SSI0_FSS (GPIO_FUNC_PFIO | GPIO_PORTA | 3) /* PA3: SSI0 frame (SSI0Fss) */
# define GPIO_SSI0_RX (GPIO_FUNC_PFINPUT | GPIO_PORTA | 4) /* PA4: SSI0 receive (SSI0Rx) */
# define GPIO_SSI0_TX (GPIO_FUNC_PFOUTPUT | GPIO_PORTA | 5) /* PA5: SSI0 transmit (SSI0Tx) */
# define GPIO_I2C0_SCL (GPIO_FUNC_PFOUTPUT | GPIO_PORTB | 2) /* PB2: I2C0 clock (I2C0SCL) */
# define GPIO_I2C0_SDA (GPIO_FUNC_PFODIO | GPIO_PORTB | 3) /* PB3: I2C0 data (I2C0SDA) */
# define GPIO_CMP0_NIN (GPIO_FUNC_PFINPUT | GPIO_PORTB | 4) /* PB4: Analog comparator 0 negative input (C0-) */
# define GPIO_CMP1_NIN (GPIO_FUNC_PFINPUT | GPIO_PORTB | 5) /* PB5: Analog comparator 1 negative input (C1-) */
# define GPIO_CMP0_PIN (GPIO_FUNC_PFINPUT | GPIO_PORTB | 6) /* PB6: Analog comparator 0 positive input (C0+) */
# define GPIO_JTAG_TRST (GPIO_FUNC_PFINPUT | GPIO_PORTB | 7) /* PB7: JTAG ~TRST */
# define GPIO_JTAG_TCK (GPIO_FUNC_PFINPUT | GPIO_PORTC | 0) /* PC0: JTAG/SWD CLK */
# define GPIO_JTAG_SWCLK (GPIO_FUNC_PFINPUT | GPIO_PORTC | 0) /* PC0: JTAG/SWD CLK */
# define GPIO_JTAG_TMS (GPIO_FUNC_PFIO | GPIO_PORTC | 1) /* PC1: JTAG TMS */
# define GPIO_JTAG_SWDIO (GPIO_FUNC_PFIO | GPIO_PORTC | 1) /* PC1: JTAG SWDIO */
# define GPIO_JTAG_TDI (GPIO_FUNC_PFINPUT | GPIO_PORTC | 2) /* PC2: JTAG TDI */
# define GPIO_JTAG_TDO (GPIO_FUNC_PFOUTPUT | GPIO_PORTC | 3) /* PC3: JTAG TDO */
# define GPIO_JTAG_SWO (GPIO_FUNC_PFOUTPUT | GPIO_PORTC | 3) /* PC3: JTAG SWO */
# define GPIO_CMP1_PIN (GPIO_FUNC_PFINPUT | GPIO_PORTC | 5) /* PC5: Analog comparator 1 positive input (C1+) */
# define GPIO_CMP0_OUT (GPIO_FUNC_PFOUTPUT | GPIO_PORTC | 5) /* PC5: Analog comparator 0 output (C0o) */
# define GPIO_PWM0_0 (GPIO_FUNC_PFOUTPUT | GPIO_PORTD | 0) /* PD0: PWM Generator 0, PWM0 */
# define GPIO_PWM0_1 (GPIO_FUNC_PFOUTPUT | GPIO_PORTD | 1) /* PD1: PWM Generator 0, PWM1 */
# define GPIO_UART1_RX (GPIO_FUNC_PFINPUT | GPIO_PORTD | 2) /* PD2: UART 1 receive (U1Rx) */
# define GPIO_UART1_TX (GPIO_FUNC_PFOUTPUT | GPIO_PORTD | 3) /* PD3: UART 1 transmit (U1Tx) */
# define GPIO_PWM_FAULT (GPIO_FUNC_PFINPUT | GPIO_PORTD | 6) /* PD6: PWM Fault */
# define GPIO_TMR1_CCP (GPIO_FUNC_PFIO | GPIO_PORTD | 7) /* PD7: Capture/Compare/TMR1 (CCP1) */
# define GPIO_ETHPHY_LED1 (GPIO_FUNC_PFOUTPUT | GPIO_PORTF | 2) /* PF2: LED1 */
# define GPIO_ETHPHY_LED0 (GPIO_FUNC_PFOUTPUT | GPIO_PORTF | 3) /* PF3: LED0 */
#elif defined(CONFIG_ARCH_CHIP_LM3S6965)
# define GPIO_UART0_RX (GPIO_FUNC_PFINPUT | GPIO_PORTA | 0) /* PA0: UART 0 receive (U0Rx) */
# define GPIO_UART0_TX (GPIO_FUNC_PFOUTPUT | GPIO_PORTA | 1) /* PA1: UART 0 transmit (U0Tx) */
# define GPIO_SSI0_CLK (GPIO_FUNC_PFIO | GPIO_PORTA | 2) /* PA2: SSI0 clock (SSI0Clk) */
# define GPIO_SSI0_FSS (GPIO_FUNC_PFIO | GPIO_PORTA | 3) /* PA3: SSI0 frame (SSI0Fss) */
# define GPIO_SSI0_RX (GPIO_FUNC_PFINPUT | GPIO_PORTA | 4) /* PA4: SSI0 receive (SSI0Rx) */
# define GPIO_SSI0_TX (GPIO_FUNC_PFOUTPUT | GPIO_PORTA | 5) /* PA5: SSI0 transmit (SSI0Tx) */
# define GPIO_I2C1_SCL (GPIO_FUNC_PFOUTPUT | GPIO_PORTA | 6) /* PA6: I2C1 clock (I2C1SCL) */
# define GPIO_I2C1_SDA (GPIO_FUNC_PFODIO | GPIO_PORTA | 7) /* PA7: I2C1 data (I2C1SDA) */
# define GPIO_PWM1_2 (GPIO_FUNC_PFOUTPUT | GPIO_PORTB | 0) /* PB0: PWM Generator 1, PWM2 */
# define GPIO_PWM1_3 (GPIO_FUNC_PFOUTPUT | GPIO_PORTB | 1) /* PB1: PWM Generator 1, PWM3 */
# define GPIO_I2C0_SCL (GPIO_FUNC_PFOUTPUT | GPIO_PORTB | 2) /* PB2: I2C0 clock (I2C0SCL) */
# define GPIO_I2C0_SDA (GPIO_FUNC_PFODIO | GPIO_PORTB | 3) /* PB3: I2C0 data (I2C0SDA) */
# define GPIO_CMP0_NIN (GPIO_FUNC_PFINPUT | GPIO_PORTB | 4) /* PB4: Analog comparator 0 negative input (C0-) */
# define GPIO_CMP1_NIN (GPIO_FUNC_PFINPUT | GPIO_PORTB | 5) /* PB5: Analog comparator 1 negative input (C1-) */
# define GPIO_CMP0_PIN (GPIO_FUNC_PFINPUT | GPIO_PORTB | 6) /* PB6: Analog comparator 0 positive input (C0+) */
# define GPIO_JTAG_TRST (GPIO_FUNC_PFINPUT | GPIO_PORTB | 7) /* PB7: JTAG ~TRST */
# define GPIO_JTAG_TCK (GPIO_FUNC_PFINPUT | GPIO_PORTC | 0) /* PC0: JTAG/SWD CLK */
# define GPIO_JTAG_SWCLK (GPIO_FUNC_PFINPUT | GPIO_PORTC | 0) /* PC0: JTAG/SWD CLK */
# define GPIO_JTAG_TMS (GPIO_FUNC_PFIO | GPIO_PORTC | 1) /* PC1: JTAG TMS */
# define GPIO_JTAG_SWDIO (GPIO_FUNC_PFIO | GPIO_PORTC | 1) /* PC1: JTAG SWDIO */
# define GPIO_JTAG_TDI (GPIO_FUNC_PFINPUT | GPIO_PORTC | 2) /* PC2: JTAG TDI */
# define GPIO_JTAG_TDO (GPIO_FUNC_PFOUTPUT | GPIO_PORTC | 3) /* PC3: JTAG TDO */
# define GPIO_JTAG_SWO (GPIO_FUNC_PFOUTPUT | GPIO_PORTC | 3) /* PC3: JTAG SWO */
# define GPIO_QEI0_PHA (GPIO_FUNC_PFINPUT | GPIO_PORTC | 4) /* PC4: QEI module 0 phase A. */
# define GPIO_CMP1_PIN (GPIO_FUNC_PFINPUT | GPIO_PORTC | 5) /* PC5: Analog comparator 1 positive input (C1+) */
# define GPIO_CMP0_OUT (GPIO_FUNC_PFOUTPUT | GPIO_PORTC | 5) /* PC5: Analog comparator 0 output (C0o) */
# define GPIO_TMR3_CCP (GPIO_FUNC_PFIO | GPIO_PORTC | 6) /* PC6: Capture/Compare/PWM3 (CCP3) */
# define GPIO_QEI0_PHB (GPIO_FUNC_PFINPUT | GPIO_PORTC | 7) /* PC7: QEI module 0 phase B. */
# define GPIO_QEI0_IDX (GPIO_FUNC_PFINPUT | GPIO_PORTD | 1) /* PD0: QEI module 0 index. ) */
# define GPIO_PWM0_1 (GPIO_FUNC_PFOUTPUT | GPIO_PORTD | 1) /* PD1: PWM Generator 0, PWM1 */
# define GPIO_UART1_RX (GPIO_FUNC_PFINPUT | GPIO_PORTD | 2) /* PD2: UART 1 receive (U1Rx) */
# define GPIO_UART1_TX (GPIO_FUNC_PFOUTPUT | GPIO_PORTD | 3) /* PD3: UART 1 transmit (U1Tx) */
# define GPIO_TMR0_CCP (GPIO_FUNC_PFIO | GPIO_PORTD | 4) /* PC4: Capture/Compare/PWM0 (CCP0) */
# define GPIO_TMR2_CCP (GPIO_FUNC_PFIO | GPIO_PORTD | 5) /* PC5: Capture/Compare/PWM2 (CCP2) */
# define GPIO_PWM_FAULT (GPIO_FUNC_PFINPUT | GPIO_PORTD | 6) /* PC5: PWM Fault */
# define GPIO_TMR1_CCP (GPIO_FUNC_PFIO | GPIO_PORTD | 7) /* PC5: Capture/Compare/TMR1 (CCP1) */
# define GPIO_SSI1_CLK (GPIO_FUNC_PFIO | GPIO_PORTE | 0) /* PE0: SSI1 clock (SSI1Clk) */
# define GPIO_SSI1_FSS (GPIO_FUNC_PFIO | GPIO_PORTE | 1) /* PE1: SSI1 frame (SSI1Fss) */
# define GPIO_SSI1_RX (GPIO_FUNC_PFINPUT | GPIO_PORTE | 2) /* PE2: SSI1 receive (SSI1Rx) */
# define GPIO_SSI1_TX (GPIO_FUNC_PFOUTPUT | GPIO_PORTE | 3) /* PE3: SSI1 transmit (SSI1Tx) */
# define GPIO_PWM2_4 (GPIO_FUNC_PFOUTPUT | GPIO_PORTE | 0) /* PE0: PWM Generator 2, PWM4 */
# define GPIO_PWM2_5 (GPIO_FUNC_PFOUTPUT | GPIO_PORTE | 1) /* PE1: PWM Generator 1, PWM5 */
# define GPIO_QEI1_PHB (GPIO_FUNC_PFINPUT | GPIO_PORTE | 2) /* PE2: QEI module 1 phase B. */
# define GPIO_QEI1_PHA (GPIO_FUNC_PFINPUT | GPIO_PORTE | 3) /* PE3: QEI module 1 phase A. */
# define GPIO_PWM0_0 (GPIO_FUNC_PFOUTPUT | GPIO_PORTF | 0) /* PE4: PWM Generator 0, PWM0 */
# define GPIO_QEI1_IDX (GPIO_FUNC_PFINPUT | GPIO_PORTE | 1) /* PD0: QEI module 1 index. ) */
# define GPIO_ETHPHY_LED1 (GPIO_FUNC_PFOUTPUT | GPIO_PORTF | 2) /* PF2: LED1 */
# define GPIO_ETHPHY_LED0 (GPIO_FUNC_PFOUTPUT | GPIO_PORTF | 3) /* PF3: LED0 */
# define GPIO_UART2_RX (GPIO_FUNC_PFINPUT | GPIO_PORTG | 0) /* PA0: UART 0 receive (UGRx) */
# define GPIO_UART2_TX (GPIO_FUNC_PFOUTPUT | GPIO_PORTG | 1) /* PA1: UART 0 transmit (UGTx) */
#elif defined(CONFIG_ARCH_CHIP_LM3S9B96)
# define GPIO_UART0_RX (GPIO_FUNC_PFINPUT | GPIO_PORTA | 0) /* PA0: UART 0 receive (U0Rx) */
# define GPIO_UART0_TX (GPIO_FUNC_PFOUTPUT | GPIO_PORTA | 1) /* PA1: UART 0 transmit (U0Tx) */
# define GPIO_SSI0_CLK (GPIO_FUNC_PFIO | GPIO_PORTA | 2) /* PA2: SSI0 clock (SSI0Clk) */
# define GPIO_SSI0_FSS (GPIO_FUNC_PFIO | GPIO_PORTA | 3) /* PA3: SSI0 frame (SSI0Fss) */
# define GPIO_SSI0_RX (GPIO_FUNC_PFINPUT | GPIO_PORTA | 4) /* PA4: SSI0 receive (SSI0Rx) */
# define GPIO_SSI0_TX (GPIO_FUNC_PFOUTPUT | GPIO_PORTA | 5) /* PA5: SSI0 transmit (SSI0Tx) */
# define GPIO_I2C1_SCL (GPIO_FUNC_PFOUTPUT | GPIO_PORTA | 7) /* PA6: I2C1 clock (I2C1SCL) */
# define GPIO_I2C1_SDA (GPIO_FUNC_PFODIO | GPIO_PORTA | 7) /* PA7: I2C1 data (I2C1SDA) */
# define GPIO_PWM1_2 (GPIO_FUNC_PFOUTPUT | GPIO_PORTB | 0) /* PB0: PWM Generator 1, PWM2 */
# define GPIO_PWM1_3 (GPIO_FUNC_PFOUTPUT | GPIO_PORTB | 1) /* PB1: PWM Generator 1, PWM3 */
# define GPIO_I2C0_SCL (GPIO_FUNC_PFOUTPUT | GPIO_PORTB | 2) /* PB2: I2C0 clock (I2C0SCL) */
# define GPIO_I2C0_SDA (GPIO_FUNC_PFODIO | GPIO_PORTB | 3) /* PB3: I2C0 data (I2C0SDA) */
# define GPIO_CMP0_NIN (GPIO_FUNC_PFINPUT | GPIO_PORTB | 4) /* PB4: Analog comparator 0 negative input (C0-) */
# define GPIO_CMP1_NIN (GPIO_FUNC_PFINPUT | GPIO_PORTB | 5) /* PB5: Analog comparator 1 negative input (C1-) */
# define GPIO_CMP0_PIN (GPIO_FUNC_PFINPUT | GPIO_PORTB | 6) /* PB6: Analog comparator 0 positive input (C0+) */
# define GPIO_JTAG_TRST (GPIO_FUNC_PFINPUT | GPIO_PORTB | 7) /* PB7: JTAG ~TRST */
# define GPIO_JTAG_TCK (GPIO_FUNC_PFINPUT | GPIO_PORTC | 0) /* PC0: JTAG/SWD CLK */
# define GPIO_JTAG_SWCLK (GPIO_FUNC_PFINPUT | GPIO_PORTC | 0) /* PC0: JTAG/SWD CLK */
# define GPIO_JTAG_TMS (GPIO_FUNC_PFIO | GPIO_PORTC | 1) /* PC1: JTAG TMS */
# define GPIO_JTAG_SWDIO (GPIO_FUNC_PFIO | GPIO_PORTC | 1) /* PC1: JTAG SWDIO */
# define GPIO_JTAG_TDI (GPIO_FUNC_PFINPUT | GPIO_PORTC | 2) /* PC2: JTAG TDI */
# define GPIO_JTAG_TDO (GPIO_FUNC_PFOUTPUT | GPIO_PORTC | 3) /* PC3: JTAG TDO */
# define GPIO_JTAG_SWO (GPIO_FUNC_PFOUTPUT | GPIO_PORTC | 3) /* PC3: JTAG SWO */
# define GPIO_QEI0_PHA (GPIO_FUNC_PFINPUT | GPIO_PORTC | 4) /* PC4: QEI module 0 phase A. */
# define GPIO_CMP1_PIN (GPIO_FUNC_PFINPUT | GPIO_PORTC | 5) /* PC5: Analog comparator 1 positive input (C1+) */
# define GPIO_CMP0_OUT (GPIO_FUNC_PFOUTPUT | GPIO_PORTC | 5) /* PC5: Analog comparator 0 output (C0o) */
# define GPIO_TMR3_CCP (GPIO_FUNC_PFIO | GPIO_PORTC | 6) /* PC6: Capture/Compare/PWM3 (CCP3) */
# define GPIO_QEI0_PHB (GPIO_FUNC_PFINPUT | GPIO_PORTC | 7) /* PC7: QEI module 0 phase B. */
# define GPIO_QEI0_IDX (GPIO_FUNC_PFINPUT | GPIO_PORTD | 1) /* PD0: QEI module 0 index. ) */
# define GPIO_PWM0_1 (GPIO_FUNC_PFOUTPUT | GPIO_PORTD | 1) /* PD1: PWM Generator 0, PWM1 */
# define GPIO_UART1_RX (GPIO_FUNC_PFINPUT | GPIO_PORTD | 2) /* PD2: UART 1 receive (U1Rx) */
# define GPIO_UART1_TX (GPIO_FUNC_PFOUTPUT | GPIO_PORTD | 3) /* PD3: UART 1 transmit (U1Tx) */
# define GPIO_TMR0_CCP (GPIO_FUNC_PFIO | GPIO_PORTD | 4) /* PC4: Capture/Compare/PWM0 (CCP0) */
# define GPIO_TMR2_CCP (GPIO_FUNC_PFIO | GPIO_PORTD | 5) /* PC5: Capture/Compare/PWM2 (CCP2) */
# define GPIO_PWM_FAULT (GPIO_FUNC_PFINPUT | GPIO_PORTD | 6) /* PC5: PWM Fault */
# define GPIO_TMR1_CCP (GPIO_FUNC_PFIO | GPIO_PORTD | 7) /* PC5: Capture/Compare/TMR1 (CCP1) */
# define GPIO_SSI1_CLK (GPIO_FUNC_PFIO | GPIO_PORTE | 0) /* PE0: SSI1 clock (SSI1Clk) */
# define GPIO_SSI1_FSS (GPIO_FUNC_PFIO | GPIO_PORTE | 1) /* PE1: SSI1 frame (SSI1Fss) */
# define GPIO_SSI1_RX (GPIO_FUNC_PFINPUT | GPIO_PORTE | 2) /* PE2: SSI1 receive (SSI1Rx) */
# define GPIO_SSI1_TX (GPIO_FUNC_PFOUTPUT | GPIO_PORTE | 3) /* PE3: SSI1 transmit (SSI1Tx) */
# define GPIO_PWM2_4 (GPIO_FUNC_PFOUTPUT | GPIO_PORTE | 0) /* PE0: PWM Generator 2, PWM4 */
# define GPIO_PWM2_5 (GPIO_FUNC_PFOUTPUT | GPIO_PORTE | 1) /* PE1: PWM Generator 1, PWM5 */
# define GPIO_QEI1_PHB (GPIO_FUNC_PFINPUT | GPIO_PORTE | 2) /* PE2: QEI module 1 phase B. */
# define GPIO_QEI1_PHA (GPIO_FUNC_PFINPUT | GPIO_PORTE | 3) /* PE3: QEI module 1 phase A. */
# define GPIO_PWM0_0 (GPIO_FUNC_PFOUTPUT | GPIO_PORTF | 0) /* PE4: PWM Generator 0, PWM0 */
# define GPIO_QEI1_IDX (GPIO_FUNC_PFINPUT | GPIO_PORTE | 1) /* PD0: QEI module 1 index. ) */
# define GPIO_ETHPHY_LED1 (GPIO_FUNC_PFOUTPUT | GPIO_PORTF | 2) /* PF2: LED1 */
# define GPIO_ETHPHY_LED0 (GPIO_FUNC_PFOUTPUT | GPIO_PORTF | 3) /* PF3: LED0 */
# define GPIO_UART2_RX (GPIO_FUNC_PFINPUT | GPIO_PORTG | 0) /* PA0: UART 0 receive (UGRx) */
# define GPIO_UART2_TX (GPIO_FUNC_PFOUTPUT | GPIO_PORTG | 1) /* PA1: UART 0 transmit (UGTx) */
#elif defined(CONFIG_ARCH_CHIP_LM3S8962)
# define GPIO_UART0_RX (GPIO_FUNC_PFINPUT | GPIO_PORTA | 0) /* PA0: UART 0 receive (U0Rx) */
# define GPIO_UART0_TX (GPIO_FUNC_PFOUTPUT | GPIO_PORTA | 1) /* PA1: UART 0 transmit (U0Tx) */
# define GPIO_SSI0_CLK (GPIO_FUNC_PFIO | GPIO_PORTA | 2) /* PA2: SSI0 clock (SSI0Clk) */
# define GPIO_SSI0_FSS (GPIO_FUNC_PFIO | GPIO_PORTA | 3) /* PA3: SSI0 frame (SSI0Fss) */
# define GPIO_SSI0_RX (GPIO_FUNC_PFINPUT | GPIO_PORTA | 4) /* PA4: SSI0 receive (SSI0Rx) */
# define GPIO_SSI0_TX (GPIO_FUNC_PFOUTPUT | GPIO_PORTA | 5) /* PA5: SSI0 transmit (SSI0Tx) */
# define GPIO_TMR1_CCP (GPIO_FUNC_PFIO | GPIO_PORTA | 6) /* PA6: Capture/Compare/PWM0 (CCP1) */
# define GPIO_PWM1_2 (GPIO_FUNC_PFOUTPUT | GPIO_PORTB | 0) /* PB0: PWM Generator 1, PWM2 */
# define GPIO_PWM1_3 (GPIO_FUNC_PFOUTPUT | GPIO_PORTB | 1) /* PB1: PWM Generator 1, PWM3 */
# define GPIO_I2C0_SCL (GPIO_FUNC_PFOUTPUT | GPIO_PORTB | 2) /* PB2: I2C0 clock (I2C0SCL) */
# define GPIO_I2C0_SDA (GPIO_FUNC_PFODIO | GPIO_PORTB | 3) /* PB3: I2C0 data (I2C0SDA) */
# define GPIO_CMP0_NIN (GPIO_FUNC_PFINPUT | GPIO_PORTB | 4) /* PB4: Analog comparator 0 negative input (C0-) */
# define GPIO_CMP0_OUT (GPIO_FUNC_PFOUTPUT | GPIO_PORTB | 5) /* PB5: Analog comparator 0 output (C0o) (differs) */
# define GPIO_CMP0_PIN (GPIO_FUNC_PFINPUT | GPIO_PORTB | 6) /* PB6: Analog comparator 0 positive input (C0+) */
# define GPIO_JTAG_TRST (GPIO_FUNC_PFINPUT | GPIO_PORTB | 7) /* PB7: JTAG ~TRST */
# define GPIO_JTAG_TCK (GPIO_FUNC_PFINPUT | GPIO_PORTC | 0) /* PC0: JTAG/SWD CLK */
# define GPIO_JTAG_SWCLK (GPIO_FUNC_PFINPUT | GPIO_PORTC | 0) /* PC0: JTAG/SWD CLK */
# define GPIO_JTAG_TMS (GPIO_FUNC_PFIO | GPIO_PORTC | 1) /* PC1: JTAG TMS */
# define GPIO_JTAG_SWDIO (GPIO_FUNC_PFIO | GPIO_PORTC | 1) /* PC1: JTAG SWDIO */
# define GPIO_JTAG_TDI (GPIO_FUNC_PFINPUT | GPIO_PORTC | 2) /* PC2: JTAG TDI */
# define GPIO_JTAG_TDO (GPIO_FUNC_PFOUTPUT | GPIO_PORTC | 3) /* PC3: JTAG TDO */
# define GPIO_JTAG_SWO (GPIO_FUNC_PFOUTPUT | GPIO_PORTC | 3) /* PC3: JTAG SWO */
# define GPIO_QEI0_PHA (GPIO_FUNC_PFINPUT | GPIO_PORTC | 4) /* PC4: QEI module 0 phase A. */
# define GPIO_QEI0_PHB (GPIO_FUNC_PFINPUT | GPIO_PORTC | 6) /* PC6: QEI module 0 phase B. */
# define GPIO_CAN0_RX (GPIO_FUNC_PFINPUT | GPIO_PORTD | 0) /* PD0: CAN module RX */
# define GPIO_CAN0_TX (GPIO_FUNC_PFOUTPUT | GPIO_PORTD | 1) /* PD1: CAN module TX */
# define GPIO_UART1_RX (GPIO_FUNC_PFINPUT | GPIO_PORTD | 2) /* PD2: UART 1 receive (U1Rx) */
# define GPIO_UART1_TX (GPIO_FUNC_PFOUTPUT | GPIO_PORTD | 3) /* PD3: UART 1 transmit (U1Tx) */
# define GPIO_TMR0_CCP (GPIO_FUNC_PFIO | GPIO_PORTD | 4) /* PD4: Capture/Compare/PWM0 (CCP0) */
# define GPIO_PWM_FAULT (GPIO_FUNC_PFINPUT | GPIO_PORTD | 6) /* PD6: PWM Fault */
# define GPIO_QEI0_IDX (GPIO_FUNC_PFIO | GPIO_PORTD | 7) /* PC7: QEI module 0 index */
# define GPIO_PWM2_4 (GPIO_FUNC_PFOUTPUT | GPIO_PORTE | 0) /* PE0: PWM Generator 2, PWM4 */
# define GPIO_PWM2_5 (GPIO_FUNC_PFOUTPUT | GPIO_PORTE | 1) /* PE1: PWM Generator 1, PWM5 */
# define GPIO_QEI1_PHB (GPIO_FUNC_PFINPUT | GPIO_PORTE | 2) /* PE2: QEI module 1 phase B. */
# define GPIO_QEI1_PHA (GPIO_FUNC_PFINPUT | GPIO_PORTE | 3) /* PE3: QEI module 1 phase A. */
# define GPIO_PWM0_0 (GPIO_FUNC_PFOUTPUT | GPIO_PORTF | 0) /* PF0: PWM Generator 0, PWM0 */
# define GPIO_QEI1_IDX (GPIO_FUNC_PFINPUT | GPIO_PORTE | 1) /* PF1: QEI module 1 index. ) */
# define GPIO_ETHPHY_LED1 (GPIO_FUNC_PFOUTPUT | GPIO_PORTF | 2) /* PF2: LED1 */
# define GPIO_ETHPHY_LED0 (GPIO_FUNC_PFOUTPUT | GPIO_PORTF | 3) /* PF3: LED0 */
# define GPIO_PWM0_1 (GPIO_FUNC_PFOUTPUT | GPIO_PORTG | 1) /* PG1:PWM Generator 0, PWM1 */
#else
# error "Unknown LM3S chip"
#endif
/************************************************************************************
* Public Types
************************************************************************************/
/************************************************************************************
* Inline Functions
************************************************************************************/
#ifndef __ASSEMBLY__
/************************************************************************************
* Public Data
************************************************************************************/
#undef EXTERN
#if defined(__cplusplus)
#define EXTERN extern "C"
extern "C" {
#else
#define EXTERN extern
#endif
/****************************************************************************
* Public Function Prototypes
****************************************************************************/
/****************************************************************************
* Name: up_lowsetup
*
* Description:
* Called at the very beginning of _start. Performs low level initialization.
*
****************************************************************************/
EXTERN void up_lowsetup(void);
/****************************************************************************
* Name: lm3s_clockconfig
*
* Description:
* Called to change to new clock based on desired rcc and rcc2 settings.
* This is use to set up the initial clocking but can be used later to
* support slow clocked, low power consumption modes.
*
****************************************************************************/
EXTERN void lm3s_clockconfig(uint32_t newrcc, uint32_t newrcc2);
/****************************************************************************
* Name: up_clockconfig
*
* Description:
* Called early in the bootsequence (before .data and .bss are available)
* in order to configure initial clocking.
*
****************************************************************************/
EXTERN void up_clockconfig(void);
/****************************************************************************
* Name: lm3s_configgpio
*
* Description:
* Configure a GPIO pin based on bit-encoded description of the pin.
*
****************************************************************************/
EXTERN int lm3s_configgpio(uint32_t cfgset);
/****************************************************************************
* Name: lm3s_gpiowrite
*
* Description:
* Write one or zero to the selected GPIO pin
*
****************************************************************************/
EXTERN void lm3s_gpiowrite(uint32_t pinset, bool value);
/****************************************************************************
* Name: lm3s_gpioread
*
* Description:
* Read one or zero from the selected GPIO pin
*
****************************************************************************/
EXTERN bool lm3s_gpioread(uint32_t pinset, bool value);
/****************************************************************************
* Function: lm3s_dumpgpio
*
* Description:
* Dump all GPIO registers associated with the provided base address
*
****************************************************************************/
EXTERN int lm3s_dumpgpio(uint32_t pinset, const char *msg);
/****************************************************************************
* Name: gpio_irqinitialize
*
* Description:
* Initialize all vectors to the unexpected interrupt handler
*
****************************************************************************/
EXTERN int weak_function gpio_irqinitialize(void);
/****************************************************************************
* Function: lm3s_ethinitialize
*
* Description:
* Initialize the Ethernet driver for one interface. If the LM3S chip
* supports multiple Ethernet controllers, then bould specific logic
* must implement up_netinitialize() and call this function to initialize
* the desiresed interfaces.
*
* Parameters:
* None
*
* Returned Value:
* OK on success; Negated errno on failure.
*
* Assumptions:
*
****************************************************************************/
#if LM3S_NETHCONTROLLERS > 1
EXTERN int lm3s_ethinitialize(int intf);
#endif
/****************************************************************************
* The external functions, lm3s_spiselect, lm3s_spistatus, and
* lm3s_spicmddata must be provided by board-specific logic. These are
* implementations of the select, status, and cmddata methods of the SPI
* interface defined by struct spi_ops_s (see include/nuttx/spi.h).
* All other methods (including up_spiinitialize()) are provided by common
* logic. To use this common SPI logic on your board:
*
* 1. Provide logic in lm3s_boardinitialize() to configure SPI chip select
* pins.
* 2. Provide lm3s_spiselect() and lm3s_spistatus() functions in your
* board-specific logic. These functions will perform chip selection and
* status operations using GPIOs in the way your board is configured.
* 3. If CONFIG_SPI_CMDDATA is defined in your NuttX configuration, provide
* the lm3s_spicmddata() function in your board-specific logic. This
* functions will perform cmd/data selection operations using GPIOs in
* the way your board is configured.
* 4. Add a call to up_spiinitialize() in your low level application
* initialization logic
* 5. The handle returned by up_spiinitialize() may then be used to bind the
* SPI driver to higher level logic (e.g., calling
* mmcsd_spislotinitialize(), for example, will bind the SPI driver to
* the SPI MMC/SD driver).
*
****************************************************************************/
struct spi_dev_s;
enum spi_dev_e;
EXTERN void lm3s_spiselect(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool selected);
EXTERN uint8_t lm3s_spistatus(FAR struct spi_dev_s *dev, enum spi_dev_e devid);
#ifdef CONFIG_SPI_CMDDATA
EXTERN int lm3s_spicmddata(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool cmd);
#endif
#undef EXTERN
#if defined(__cplusplus)
}
#endif
#endif /* __ASSEMBLY__ */
#endif /* __ARCH_ARM_SRC_LM3S_LM3S_INTERNAL_H */
