diff options
-rw-r--r-- | nuttx/configs/sama5d3-xplained/src/sam_sdram.c | 6 | ||||
-rw-r--r-- | nuttx/configs/sama5d3x-ek/README.txt | 32 | ||||
-rw-r--r-- | nuttx/configs/sama5d3x-ek/src/sam_sdram.c | 6 |
3 files changed, 29 insertions, 15 deletions
diff --git a/nuttx/configs/sama5d3-xplained/src/sam_sdram.c b/nuttx/configs/sama5d3-xplained/src/sam_sdram.c index c9cf8a5ea..8190d7cca 100644 --- a/nuttx/configs/sama5d3-xplained/src/sam_sdram.c +++ b/nuttx/configs/sama5d3-xplained/src/sam_sdram.c @@ -112,13 +112,13 @@ #if defined(CONFIG_SAMA5D3XPLAINED_384MHZ) # define NSEC_TO_COUNT(nsec) ((((nsec) * 1000) / 15625) + LOOP_GUARD) -# define USEC_TO_COUNT(usec) (((usec) * 1000000) / 15625) + LOOP_GUARD) +# define USEC_TO_COUNT(usec) ((((usec) * 1000000) / 15625) + LOOP_GUARD) #elif defined(CONFIG_SAMA5D3XPLAINED_528MHZ) # define NSEC_TO_COUNT(nsec) ((((nsec) * 1000) / 11364) + LOOP_GUARD) -# define USEC_TO_COUNT(usec) (((usec) * 1000000) / 11364) + LOOP_GUARD) +# define USEC_TO_COUNT(usec) ((((usec) * 1000000) / 11364) + LOOP_GUARD) #else /* #elif defined(CONFIG_SAMA5D3XPLAINED_396MHZ) */ # define NSEC_TO_COUNT(nsec) ((((nsec) * 1000) / 15152) + LOOP_GUARD) -# define USEC_TO_COUNT(usec) (((usec) * 1000000) / 15152) + LOOP_GUARD) +# define USEC_TO_COUNT(usec) ((((usec) * 1000000) / 15152) + LOOP_GUARD) #endif /**************************************************************************** diff --git a/nuttx/configs/sama5d3x-ek/README.txt b/nuttx/configs/sama5d3x-ek/README.txt index a6a52752c..bda6bbcbf 100644 --- a/nuttx/configs/sama5d3x-ek/README.txt +++ b/nuttx/configs/sama5d3x-ek/README.txt @@ -1436,11 +1436,6 @@ USB High-Speed Host Application Configuration -> NSH Library CONFIG_NSH_ARCHINIT=y : NSH board-initialization - NOTE: When OHCI is selected, the SAMA5 will operate at 384MHz instead of - 396MHz. This is so that the PLL generates a frequency which is a multiple - of the 48MHz needed for OHCI. The delay loop calibration values that are - used will be off slightly because of this. - EHCI ---- @@ -1630,7 +1625,7 @@ SDRAM Support CONFIG_SYSTEM_RAMTEST=y In this configuration, the SDRAM is not added to heap and so is not - accessable to the applications. So the RAM test can be freely executed + accessible to the applications. So the RAM test can be freely executed against the SRAM memory beginning at address 0x2000:0000 (DDR CS): nsh> ramtest -h @@ -3389,9 +3384,28 @@ To-Do List 1) Currently the SAMA5Dx is running at 396MHz in these configurations. This is because the timing for the PLLs, NOR FLASH, and SDRAM came from the - Atmel NoOS sample code which runs at that rate. The SAMA5Dx is capable - of running at 528MHz, however. The setup for that configuration exists - in the Bareboard assembly language setup and should be incorporated. + Atmel NoOS sample code which runs at that rate. + + The SAMA5Dx is capable of running at 528MHz, however, and is easily + configured: + + Board Selection -> CPU Frequency + CONFIG_SAMA5D3xEK_396MHZ=n + CONFIG_SAMA5D3xEK_528MHZ=y + + Basic operation at 528MHz has been verified but is not the default in + these configurations because most testing was done at 396MHz. + + - The apps/system/ramtest runs without errors, but runs very slowly. + It looks like it takes about 90 seconds to test 1MiB of RAM. That + means that a full 256MiB RAM test should take about 6 hours. That + is too long. This implies that there is something wrong with the + SDRAM configuration. + - Similarly, while attempting to calibrate the delay loop, I find that + the 100s calibration delay runs for a very long time. This is not + correct, of course, with a higher CPU clock, the calibration delay + should be shorter if anything! + - NAND time has not been tested. 2) Most of these configurations execute from NOR FLASH. I have been unable to execute these configurations from NOR FLASH by closing the BMS jumper diff --git a/nuttx/configs/sama5d3x-ek/src/sam_sdram.c b/nuttx/configs/sama5d3x-ek/src/sam_sdram.c index efb40684a..080ed9a12 100644 --- a/nuttx/configs/sama5d3x-ek/src/sam_sdram.c +++ b/nuttx/configs/sama5d3x-ek/src/sam_sdram.c @@ -112,13 +112,13 @@ #if defined(CONFIG_SAMA5D3xEK_384MHZ) # define NSEC_TO_COUNT(nsec) ((((nsec) * 1000) / 15625) + LOOP_GUARD) -# define USEC_TO_COUNT(usec) (((usec) * 1000000) / 15625) + LOOP_GUARD) +# define USEC_TO_COUNT(usec) ((((usec) * 1000000) / 15625) + LOOP_GUARD) #elif defined(CONFIG_SAMA5D3xEK_528MHZ) # define NSEC_TO_COUNT(nsec) ((((nsec) * 1000) / 11364) + LOOP_GUARD) -# define USEC_TO_COUNT(usec) (((usec) * 1000000) / 11364) + LOOP_GUARD) +# define USEC_TO_COUNT(usec) ((((usec) * 1000000) / 11364) + LOOP_GUARD) #else /* #elif defined(CONFIG_SAMA5D3xEK_396MHZ) */ # define NSEC_TO_COUNT(nsec) ((((nsec) * 1000) / 15152) + LOOP_GUARD) -# define USEC_TO_COUNT(usec) (((usec) * 1000000) / 15152) + LOOP_GUARD) +# define USEC_TO_COUNT(usec) ((((usec) * 1000000) / 15152) + LOOP_GUARD) #endif /**************************************************************************** |