/****************************************************************************
*
* Copyright (C) 2012 PX4 Development Team. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name PX4 nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
/**
* @file px4fmu_init.c
*
* PX4FMU-specific early startup code. This file implements the
* nsh_archinitialize() function that is called early by nsh during startup.
*
* Code here is run before the rcS script is invoked; it should start required
* subsystems and perform board-specific initialisation.
*/
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <stdbool.h>
#include <stdio.h>
#include <debug.h>
#include <errno.h>
#include <nuttx/arch.h>
#include <nuttx/spi.h>
#include <nuttx/i2c.h>
#include <nuttx/mmcsd.h>
#include <nuttx/analog/adc.h>
#include <nuttx/arch.h>
#include "stm32_internal.h"
#include "px4fmu_internal.h"
#include "stm32_uart.h"
#include <arch/board/up_adc.h>
#include <arch/board/board.h>
#include <arch/board/drv_led.h>
#include <arch/board/drv_eeprom.h>
#include <drivers/drv_hrt.h>
#include <systemlib/cpuload.h>
/****************************************************************************
* Pre-Processor Definitions
****************************************************************************/
/* Configuration ************************************************************/
/* Debug ********************************************************************/
#ifdef CONFIG_CPP_HAVE_VARARGS
# ifdef CONFIG_DEBUG
# define message(...) lib_lowprintf(__VA_ARGS__)
# else
# define message(...) printf(__VA_ARGS__)
# endif
#else
# ifdef CONFIG_DEBUG
# define message lib_lowprintf
# else
# define message printf
# endif
#endif
/****************************************************************************
* Protected Functions
****************************************************************************/
/****************************************************************************
* Public Functions
****************************************************************************/
/************************************************************************************
* Name: stm32_boardinitialize
*
* Description:
* All STM32 architectures must provide the following entry point. This entry point
* is called early in the intitialization -- after all memory has been configured
* and mapped but before any devices have been initialized.
*
************************************************************************************/
__EXPORT void stm32_boardinitialize(void)
{
/* configure SPI interfaces */
stm32_spiinitialize();
/* configure LEDs */
up_ledinit();
}
/****************************************************************************
* Name: nsh_archinitialize
*
* Description:
* Perform architecture specific initialization
*
****************************************************************************/
static struct spi_dev_s *spi1;
static struct spi_dev_s *spi3;
static struct i2c_dev_s *i2c1;
static struct i2c_dev_s *i2c2;
static struct i2c_dev_s *i2c3;
#include <math.h>
#ifdef __cplusplus
__EXPORT int matherr(struct __exception *e) {
return 1;
}
#else
__EXPORT int matherr(struct exception *e) {
return 1;
}
#endif
__EXPORT int nsh_archinitialize(void)
{
int result;
/* INIT 1 Lowest level NuttX initialization has been done at this point, LEDs and UARTs are configured */
/* INIT 2 Configuring PX4 low-level peripherals, these will be always needed */
/* configure the high-resolution time/callout interface */
#ifdef CONFIG_HRT_TIMER
hrt_init();
#endif
/* configure CPU load estimation */
#ifdef CONFIG_SCHED_INSTRUMENTATION
cpuload_initialize_once();
#endif
/* set up the serial DMA polling */
#ifdef SERIAL_HAVE_DMA
{
static struct hrt_call serial_dma_call;
struct timespec ts;
/*
* Poll at 1ms intervals for received bytes that have not triggered
* a DMA event.
*/
ts.tv_sec = 0;
ts.tv_nsec = 1000000;
hrt_call_every(&serial_dma_call,
ts_to_abstime(&ts),
ts_to_abstime(&ts),
(hrt_callout)stm32_serial_dma_poll,
NULL);
}
#endif
message("\r\n");
up_ledoff(LED_BLUE);
up_ledoff(LED_AMBER);
up_ledon(LED_BLUE);
/* Configure user-space led driver */
px4fmu_led_init();
/* Configure SPI-based devices */
spi1 = up_spiinitialize(1);
if (!spi1)
{
message("[boot] FAILED to initialize SPI port 1\r\n");
up_ledon(LED_AMBER);
return -ENODEV;
}
// Default SPI1 to 1MHz and de-assert the known chip selects.
SPI_SETFREQUENCY(spi1, 10000000);
SPI_SETBITS(spi1, 8);
SPI_SETMODE(spi1, SPIDEV_MODE3);
SPI_SELECT(spi1, PX4_SPIDEV_GYRO, false);
SPI_SELECT(spi1, PX4_SPIDEV_ACCEL, false);
SPI_SELECT(spi1, PX4_SPIDEV_MPU, false);
up_udelay(20);
message("[boot] Successfully initialized SPI port 1\r\n");
/* initialize I2C2 bus */
i2c2 = up_i2cinitialize(2);
if (!i2c2) {
message("[boot] FAILED to initialize I2C bus 2\n");
up_ledon(LED_AMBER);
return -ENODEV;
}
/* set I2C2 speed */
I2C_SETFREQUENCY(i2c2, 400000);
i2c3 = up_i2cinitialize(3);
if (!i2c3) {
message("[boot] FAILED to initialize I2C bus 3\n");
up_ledon(LED_AMBER);
return -ENODEV;
}
/* set I2C3 speed */
I2C_SETFREQUENCY(i2c3, 400000);
/* try to attach, don't fail if device is not responding */
(void)eeprom_attach(i2c3, FMU_BASEBOARD_EEPROM_ADDRESS,
FMU_BASEBOARD_EEPROM_TOTAL_SIZE_BYTES,
FMU_BASEBOARD_EEPROM_PAGE_SIZE_BYTES,
FMU_BASEBOARD_EEPROM_PAGE_WRITE_TIME_US, "/dev/baseboard_eeprom", 1);
#if defined(CONFIG_STM32_SPI3)
/* Get the SPI port */
message("[boot] Initializing SPI port 3\n");
spi3 = up_spiinitialize(3);
if (!spi3)
{
message("[boot] FAILED to initialize SPI port 3\n");
up_ledon(LED_AMBER);
return -ENODEV;
}
message("[boot] Successfully initialized SPI port 3\n");
/* Now bind the SPI interface to the MMCSD driver */
result = mmcsd_spislotinitialize(CONFIG_NSH_MMCSDMINOR, CONFIG_NSH_MMCSDSLOTNO, spi3);
if (result != OK)
{
message("[boot] FAILED to bind SPI port 3 to the MMCSD driver\n");
up_ledon(LED_AMBER);
return -ENODEV;
}
message("[boot] Successfully bound SPI port 3 to the MMCSD driver\n");
#endif /* SPI3 */
/* initialize I2C1 bus */
i2c1 = up_i2cinitialize(1);
if (!i2c1) {
message("[boot] FAILED to initialize I2C bus 1\n");
up_ledon(LED_AMBER);
return -ENODEV;
}
/* set I2C1 speed */
I2C_SETFREQUENCY(i2c1, 400000);
/* INIT 3: MULTIPORT-DEPENDENT INITIALIZATION */
/* Get board information if available */
/* Initialize the user GPIOs */
px4fmu_gpio_init();
#ifdef CONFIG_ADC
int adc_state = adc_devinit();
if (adc_state != OK)
{
/* Try again */
adc_state = adc_devinit();
if (adc_state != OK)
{
/* Give up */
message("[boot] FAILED adc_devinit: %d\n", adc_state);
return -ENODEV;
}
}
#endif
return OK;
}