diff options
Diffstat (limited to 'nuttx/configs')
-rwxr-xr-x | nuttx/configs/stm3240g-eval/README.txt | 19 | ||||
-rwxr-xr-x | nuttx/configs/stm3240g-eval/include/board.h | 22 | ||||
-rwxr-xr-x | nuttx/configs/stm3240g-eval/nsh/defconfig | 33 | ||||
-rwxr-xr-x | nuttx/configs/stm3240g-eval/ostest/defconfig | 33 |
4 files changed, 102 insertions, 5 deletions
diff --git a/nuttx/configs/stm3240g-eval/README.txt b/nuttx/configs/stm3240g-eval/README.txt index 2cd5339e4..25ee3ce34 100755 --- a/nuttx/configs/stm3240g-eval/README.txt +++ b/nuttx/configs/stm3240g-eval/README.txt @@ -374,10 +374,29 @@ STM3240G-EVAL-specific Configuration Options CONFIG_SDIO_WIDTH_D1_ONLY - Select 1-bit transfer mode. Default: 4-bit transfer mode. + CONFIG_STM32_PHYADDR - The 5-bit address of the PHY on the board CONFIG_STM32_MII - Support Ethernet MII interface CONFIG_STM32_MII_MCO1 - Use MCO1 to clock the MII interface CONFIG_STM32_MII_MCO2 - Use MCO2 to clock the MII interface CONFIG_STM32_RMII - Support Ethernet RMII interface + CONFIG_STM32_AUTONEG - Use PHY autonegotion to determine speed and mode + CONFIG_STM32_ETHFD - If CONFIG_STM32_AUTONEG is not defined, then this + may be defined to select full duplex mode. Default: half-duplex + CONFIG_STM32_ETH100MBPS - If CONFIG_STM32_AUTONEG is not defined, then this + may be defined to select 100 MBps speed. Default: 10 Mbps + CONFIG_STM32_PHYSR - This must be provided if CONFIG_STM32_AUTONEG is + defined. The PHY status register address may diff from PHY to PHY. This + configuration sets the address of the PHY status register. + CONFIG_STM32_PHYSR_SPEED - This must be provided if CONFIG_STM32_AUTONEG is + defined. This provides bit mask indicating 10 or 100MBps speed. + CONFIG_STM32_PHYSR_100MBPS - This must be provided if CONFIG_STM32_AUTONEG is + defined. This provides the value of the speed bit(s) indicating 100MBps speed. + CONFIG_STM32_PHYSR_MODE - This must be provided if CONFIG_STM32_AUTONEG is + defined. This provide bit mask indicating full or half duplex modes. + CONFIG_STM32_PHYSR_FULLDUPLEX - This must be provided if CONFIG_STM32_AUTONEG is + defined. This provides the value of the mode bits indicating full duplex mode. + CONFIG_STM32_ETH_PTP - Precision Time Protocol (PTP). Not supported + but some hooks are indicated with this condition. STM3240G-EVAL LCD Hardware Configuration diff --git a/nuttx/configs/stm3240g-eval/include/board.h b/nuttx/configs/stm3240g-eval/include/board.h index 1a1c6738f..663ad7eda 100755 --- a/nuttx/configs/stm3240g-eval/include/board.h +++ b/nuttx/configs/stm3240g-eval/include/board.h @@ -172,8 +172,26 @@ # define SDIO_SDXFR_CLKDIV (3 << SDIO_CLKCR_CLKDIV_SHIFT) #endif -/* LED definitions ******************************************************************/ +/* Ethernet *************************************************************************/ +/* We need to provide clocking to the MII PHY via MCO1 (PA8) */ + +#if defined(CONFIG_NET) && defined(CONFIG_STM32_ETHMAC) + +# if !defined(CONFIG_STM32_MII) +# warning "CONFIG_STM32_MII required for Ethernet" +# elif !defined(CONFIG_STM32_MII_MCO1) +# warning "CONFIG_STM32_MII_MCO1 required for Ethernet MII" +# else + + /* Output HSE clock (25MHz) on MCO1 pin (PA8) to clock the PHY */ + +# define BOARD_CFGR_MC01_SOURCE RCC_CFGR_MCO1_HSE +# define BOARD_CFGR_MC01_DIVIDER RCC_CFGR_MCO1PRE_NONE +# endif +#endif + +/* LED definitions ******************************************************************/ /* The STM3240G-EVAL board has 4 LEDs that we will encode as: */ #define LED_STARTED 0 /* LED1 */ @@ -185,6 +203,7 @@ #define LED_ASSERTION 6 /* LED1 + LED2 + LED3 */ #define LED_PANIC 7 /* N/C + N/C + N/C + LED4 */ +/* Button definitions ***************************************************************/ /* The STM3240G-EVAL supports three buttons: */ #define BUTTON_WAKEUP 0 @@ -200,6 +219,7 @@ /* Alternate function pin selections ************************************************/ /* UART3: + * * - PC11 is MicroSDCard_D3 & RS232/IrDA_RX (JP22 open) * - PC10 is MicroSDCard_D2 & RSS232/IrDA_TX */ diff --git a/nuttx/configs/stm3240g-eval/nsh/defconfig b/nuttx/configs/stm3240g-eval/nsh/defconfig index 490b32a7b..ce69e0295 100755 --- a/nuttx/configs/stm3240g-eval/nsh/defconfig +++ b/nuttx/configs/stm3240g-eval/nsh/defconfig @@ -258,15 +258,44 @@ CONFIG_SSI_POLLWAIT=y # # STM32F40xxx Ethernet device driver settings # +# CONFIG_STM32_PHYADDR - The 5-bit address of the PHY on the board # CONFIG_STM32_MII - Support Ethernet MII interface # CONFIG_STM32_MII_MCO1 - Use MCO1 to clock the MII interface # CONFIG_STM32_MII_MCO2 - Use MCO2 to clock the MII interface # CONFIG_STM32_RMII - Support Ethernet RMII interface -# +# CONFIG_STM32_AUTONEG - Use PHY autonegotion to determine speed and mode +# CONFIG_STM32_ETHFD - If CONFIG_STM32_AUTONEG is not defined, then this +# may be defined to select full duplex mode. Default: half-duplex +# CONFIG_STM32_ETH100MBPS - If CONFIG_STM32_AUTONEG is not defined, then this +# may be defined to select 100 MBps speed. Default: 10 Mbps +# CONFIG_STM32_PHYSR - This must be provided if CONFIG_STM32_AUTONEG is +# defined. The PHY status register address may diff from PHY to PHY. This +# configuration sets the address of the PHY status register. +# CONFIG_STM32_PHYSR_SPEED - This must be provided if CONFIG_STM32_AUTONEG is +# defined. This provides bit mask indicating 10 or 100MBps speed. +# CONFIG_STM32_PHYSR_100MBPS - This must be provided if CONFIG_STM32_AUTONEG is +# defined. This provides the value of the speed bit(s) indicating 100MBps speed. +# CONFIG_STM32_PHYSR_MODE - This must be provided if CONFIG_STM32_AUTONEG is +# defined. This provide bit mask indicating full or half duplex modes. +# CONFIG_STM32_PHYSR_FULLDUPLEX - This must be provided if CONFIG_STM32_AUTONEG is +# defined. This provides the value of the mode bits indicating full duplex mode. +# CONFIG_STM32_ETH_PTP - Precision Time Protocol (PTP). Not supported +# but some hooks are indicated with this condition. +# +CONFIG_STM32_PHYADDR=0x01 CONFIG_STM32_MII=y CONFIG_STM32_MII_MCO1=y CONFIG_STM32_MII_MCO2=n CONFIG_STM32_RMII=n +CONFIG_STM32_AUTONEG=y +#CONFIG_STM32_ETHFD +#CONFIG_STM32_ETH100MB +CONFIG_STM32_PHYSR=16 +CONFIG_STM32_PHYSR_SPEED=0x0002 +CONFIG_STM32_PHYSR_100MBPS=0x0000 +CONFIG_STM32_PHYSR_MODE=0x0004 +CONFIG_STM32_PHYSR_FULLDUPLEX=0x0004 +CONFIG_STM32_ETH_PTP=n # # General build options @@ -684,7 +713,7 @@ CONFIG_NET=n CONFIG_NET_IPv6=n CONFIG_NSOCKET_DESCRIPTORS=10 CONFIG_NET_SOCKOPTS=y -CONFIG_NET_BUFSIZE=420 +CONFIG_NET_BUFSIZE=562 CONFIG_NET_TCP=y CONFIG_NET_TCP_CONNS=40 CONFIG_NET_MAX_LISTENPORTS=40 diff --git a/nuttx/configs/stm3240g-eval/ostest/defconfig b/nuttx/configs/stm3240g-eval/ostest/defconfig index cced8c8f2..cc91d8a53 100755 --- a/nuttx/configs/stm3240g-eval/ostest/defconfig +++ b/nuttx/configs/stm3240g-eval/ostest/defconfig @@ -258,15 +258,44 @@ CONFIG_SSI_POLLWAIT=y # # STM32F40xxx Ethernet device driver settings # +# CONFIG_STM32_PHYADDR - The 5-bit address of the PHY on the board # CONFIG_STM32_MII - Support Ethernet MII interface # CONFIG_STM32_MII_MCO1 - Use MCO1 to clock the MII interface # CONFIG_STM32_MII_MCO2 - Use MCO2 to clock the MII interface # CONFIG_STM32_RMII - Support Ethernet RMII interface -# +# CONFIG_STM32_AUTONEG - Use PHY autonegotion to determine speed and mode +# CONFIG_STM32_ETHFD - If CONFIG_STM32_AUTONEG is not defined, then this +# may be defined to select full duplex mode. Default: half-duplex +# CONFIG_STM32_ETH100MBPS - If CONFIG_STM32_AUTONEG is not defined, then this +# may be defined to select 100 MBps speed. Default: 10 Mbps +# CONFIG_STM32_PHYSR - This must be provided if CONFIG_STM32_AUTONEG is +# defined. The PHY status register address may diff from PHY to PHY. This +# configuration sets the address of the PHY status register. +# CONFIG_STM32_PHYSR_SPEED - This must be provided if CONFIG_STM32_AUTONEG is +# defined. This provides bit mask indicating 10 or 100MBps speed. +# CONFIG_STM32_PHYSR_100MBPS - This must be provided if CONFIG_STM32_AUTONEG is +# defined. This provides the value of the speed bit(s) indicating 100MBps speed. +# CONFIG_STM32_PHYSR_MODE - This must be provided if CONFIG_STM32_AUTONEG is +# defined. This provide bit mask indicating full or half duplex modes. +# CONFIG_STM32_PHYSR_FULLDUPLEX - This must be provided if CONFIG_STM32_AUTONEG is +# defined. This provides the value of the mode bits indicating full duplex mode. +# CONFIG_STM32_ETH_PTP - Precision Time Protocol (PTP). Not supported +# but some hooks are indicated with this condition. +# +CONFIG_STM32_PHYADDR=0x01 CONFIG_STM32_MII=y CONFIG_STM32_MII_MCO1=y CONFIG_STM32_MII_MCO2=n CONFIG_STM32_RMII=n +CONFIG_STM32_AUTONEG=y +#CONFIG_STM32_ETHFD +#CONFIG_STM32_ETH100MBPS +CONFIG_STM32_PHYSR=16 +CONFIG_STM32_PHYSR_SPEED=0x0002 +CONFIG_STM32_PHYSR_100MBPS=0x0000 +CONFIG_STM32_PHYSR_MODE=0x0004 +CONFIG_STM32_PHYSR_FULLDUPLEX=0x0004 +CONFIG_STM32_ETH_PTP=n # # General build options @@ -648,7 +677,7 @@ CONFIG_NET=n CONFIG_NET_IPv6=n CONFIG_NSOCKET_DESCRIPTORS=0 CONFIG_NET_SOCKOPTS=y -CONFIG_NET_BUFSIZE=420 +CONFIG_NET_BUFSIZE=562 CONFIG_NET_TCP=n CONFIG_NET_TCP_CONNS=40 CONFIG_NET_MAX_LISTENPORTS=40 |